Sunday, June 26, 2011

UTM: Troubleshooting LDAP over TLS integration with SonicWall

Article Applies To:
Affected SonicWALL Security Appliance Platforms:

Gen5: NSA E7500, NSA E6500, NSA E5500, NSA 5000, NSA 4500, NSA 3500, NSA 2400, NSA 240
Gen4: PRO series: PRO 5060, PRO 4100, PRO 4060,PRO 3060, PRO 2040, PRO 1260
TZ series: TZ 210, TZ 210 Wireless, TZ 190, TZ 190 W, TZ 180, TZ 180 W, TZ 170, TZ 170 W, TZ 170 SP, TZ 170 SP Wireless.
Affected Firmware versions: All Gen5 and Gen4 firmware versions (SonicOS Enhanced)
Affected Services: LDAP

Problem Definition:

The following error messages are addressed in this article.

- Problem contacting LDAP server
- Credentials not valid at LDAP server. or Credentials not valid at LDAP server - 80090308: LdapErr: DSID-0C090334, comment: AcceptSecurityContext error, data 525, vece
- LDAP Authentication failed.
- BAD LDAP server certificate TLS error unknown CA

More error messages and solutions related to LDAP integration can be found at the below link: http://support.microsoft.com/kb/823659

Kernel debugging Windows XP inside of a virtual machine

Something that is incredibly easy to do with virtual machines is kernel debugging. You can do this by either connecting two virtual machines to the same named pipe (creating a virtual null-modem cable as it were), or by debugging a virtual machine directly over a named pipe from the host operating system.  If you are using two virtual machines you will need to configure both to have COM1 connected to a shared named pipe (e.g. \\.\pipe\debugPipe).  If you are going to debug a virtual machine from your host computer you will just need to configure the one virtual machine to have its COM1 connected to the named pipe. You will then need to start the virtual machine you want to debug and do the following:

How to Hide or Unhide a User Account in Vista

How to Hide or Unhide a User Account in Vista
Published by Brink
09-25-2007


METHOD ONE:  Through Local Users and Groups Manager

NOTE
This method is only available for the Vista Business, Ultimate, and Enterprise editions. See Method Two below for the Vista Home Basic and Home Premium editions.

1. Open the Local Users and Groups manager.

2. In the left pane click on the Users folder. (See screenshot below)

Note:  This method is only available for the Vista Business, Ultimate, and Enterprise editions. See Method Two below for the Vista Home Basic and Home Premium editions.

Configuring the Windows Time Service

This article walks you through the process of setting up an authoritative time server for a Windows Server 2003-based network running Active Directory. The article outlines procedures for syncing to both an internal and external time source, and also lists additional resources for configuring the Windows Time service and troubleshooting time synchronization problems.

The Windows Time service (W32Time) is designed to maintain date and time synchronization for computers running Windows 2000XP/2003. The primary use for such time synchronization is to ensure the security of Kerberos authentication within an Active Directory environment. To prevent replay attacks, Kerberos tickets presented to domain controllers by clients are time-stamped. The authenticating domain controller checks to make sure the timestamp is unique and falls within an allowable skew before accepting the ticket and authenticating the client. To ensure this system works properly, both the client and the domain controller clocks must be loosely synchronized within the allowable skew, and W32Time ensures this is the case.

W32Time is based on the Simple Network Time Protocol (SNTP) as specified in RFC RFC 1769 (now superceded by RFC 2030). SNTP is designed to ensure loose synchronization only, which in the W32Time implementation means the clocks of all Windows 2000/XP/2003 machines in a forest will agree within 20 seconds of one another (or 2 seconds difference within a particular site). W32Time expresses clock times in Coordinated Universal Time (UTC), an atomic time scale previously known as Greenwich Mean Time (GMT). W32Time is started by default on Windows XP and Windows Server 2003 machines regardless of whether they belong to a workgroup or a domain. On Windows 2000 however, W32Time must be manually started on machines belonging to a workgroup.

Saturday, June 25, 2011

Create a Hidden User Account

Others may want to log in to XP under your name. Hide your user account and remove the temptation.

User accounts normally appear on your Windows XP welcome screen. Today I'll show you a Windows tweak that lets you hide 'em from view. It only applies to a user account you've already created, so if you want to hide a completely new account, you must also create that account!

You'll need to go into your Registry, so back it up before you start just in case you make a mistake. Here's how to hide your user account.

How to reset Internet Protocol in XP

Please understand that this content is directly received from Microsoft. This is not our content, I don't own it, I didn't write it, I'm simply making it available in a format that allows my blog system.

The original article on Microsoft.com can be found here.

Microsoft Legal Links Terms of use Security & Privacy Accessibility

 

How to reset Internet Protocol (TCP/IP) in Windows XP

Article ID:299357
Last Review:July 12, 2004
Revision:1.0
This article was previously published under Q299357
For a Microsoft Windows Server 2003 version of this article, see 317518.

INTRODUCTION

In Microsoft Windows XP, the TCP/IP stack is considered a core component of the operating system, and you cannot remove TCP/IP. Therefore, when you view the list of components for a network interface, you may notice that the Uninstall button is disabled when Internet Protocol (TCP/IP) is selected. In extreme cases, the best solution for this issue may be to reinstall the Internet Protocol stack. But with the NetShell utility, you can reset the TCP/IP stack to restore it to its state that existed when the operating system was installed. This article describes how to use the NetShell utility for this purpose.

Installing Your Website's Certificate in Internet Explorer

I know it gets irritating overtime when you visit your own secured website from outside your network and stopped by Internet Explorer stating that there is a problem with this website's security certificate. It is your own secured website and you know that there is no problem with its security certificate. BTW, you will get this prompt only if you installed a certificate approved by your own Windows Certificate server in to your website. So to bypass this prompt is to install your website's certificate in IE.

Here is the dilemma. In Firefox, you need to install a certificate just once whether that certificate was approved by your own Windows Certificate server or from a known certificate distributor like Verisign. Firefox will not prompt you again once you installed the website's certificate. In IE, it will keep prompting you even after you installed the website's certificate approved by your own Windows Certificate server unless, you follow these steps.

How to Disable Chkdsk at Startup

There are two ways to do this. First, open the Command prompt and type this command to disable chkdsk at startup for the C: drive: chkntfs c: /x. You can use the same command for the other drives by just replacing the drive letter.

The second way is to modify your registry setting. Just make sure to create a backup of the registry first before making any changes. So to disable chkdsk at startup by modifying your registry go to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager and change the BootExecute entry to: autocheck autochk /k:C * .

If you want to restore everything to default, just replace the key with the default one i.e. autocheck autochk *.

Moving the Offline Files Cache in Windows Vista

How to move the Offline Files cache location from the default location (c:\windows\csc) to another volume.

1.  From an elevated command prompt, run the following command: 

REG ADD "HKLM\System\CurrentControlSet\Services\CSC\Parameters" /v MigrationParameters /t REG_DWORD /d 1 /f \

2.  Run the following command as a user who is a local administrator, substituting the drive letter if necessary:  c:\windows\system32\migwiz\migwiz.exe

Customize the "NewForm.aspx" page for a SharePoint List

from: Winsmarts.com
Creating a SharePoint list is hella easy. Point and click - and bingo - you have a form to type in and maintain your data in a structure you specified, and you can then create various views on the data collected.

But what if you wished to customize either the "New" form, or the "Update" form etc?
In this blogpost, I will demonstrate how to customize the New form for the announcements list.

Open Links in New Window

There must be a better way to open links in a new window. Here is my version of doing it. Let's say you want to open Google website. Just use this code as the URL and it should open Google in a new window.
 
javascript:window.open('http://www.google.com','_blank');history.go(0))

Hyper-V How To: Change the HAL on your vm

When you migrate your Virtual Server or Virtual PC virtual machine to Hyper-V, you:
  • remove the VM Additions
  • move the VHD
  • create a new VM
  • install the Integration Services in the new VM
If you have trouble in this process, and it looks like the integration services did non install correctly (mouse doesn't work correctly, for example), you may have a HAL mismatch.
By default, Hyper-V will install an APIC MP HAL when the Integration Services are installed in the virtual machine. If the VM had a different HAL, try changing it.

How to perform a silent install of the Backup Exec Remote Agent for Windows NT and 2000


How to perform a silent install of the Backup Exec Remote Agent for Windows NT and 2000, previously known as the Agent Accelerator, from a command prompt

Details:
To perform a silent install of the VERITAS Backup Exec (tm) Remote Agent for Windows NT and 2000, previously known as the Agent Accelerator, from a command prompt, please perform either of the following:

Option 1
1. Share out the CD-ROM drive on the backup server

OR